So I entered my wife into the 8800 club for Christmas (I actually installed the card on Sunday). Everything worked great on Sunday, and Monday, but this morning, Minerva's computer wouldn't post. Fans spin, drives spin, but no beeps and no display. I already tried resetting the BIOS, but no luck there. Any thoughts?
-
-
Take the card out put it back on mate then check your power lead to the card This happend to me with my 8800GT card after this the card was working fine. -
Also make sure the PSU can handle everything plus the new card.
Apache
Where do you put the Bayonet?
Chesty Puller (upon seeing a flamethrower for the first time)
I am all in favor of keeping dangerous weapons out of the hands of fools. Lets start with typewriters.
Frank Lloyd WrightComment
-
+1 to the above. Hope you get it working but we'll be here if it doesn't Enjoy Minerva!
Comment
-
The same exact thing happens to my 8600GT, the second day it was installed. Take out the CMOS battery and pop it back in 30 minutes(ish) later. It should start up and it will say Checksum is bad, you'll have to reset the clock/date in BIOS.Comment
-
I vacummed the cpu yesterday and the computer was on, but I wasn't using it because I had to get ready for Christmas Eve. Can that be related to this issue?
K3BASFM. "Lead, follow, or get out of the way."
sigpic
Support Cainslair. Donate here! Cain's Lair ForumsComment
-
May be buck they one way to be sure pop you old card back in and try it if the card works then it you new 8800 card that As broken down.Originally posted by MinervaRelefenI vacummed the cpu yesterday and the computer was on, but I wasn't using it because I had to get ready for Christmas Eve. Can that be related to this issue?Comment
-
Thanks for the advice everyone, but the issue was that the Northbridge fan was clogged with dust. I mean, like, CLOGGED. I am guessing this is what was causing the boot failure. Anyway, the new motherboard is working great, just one teeny tiny issue. The new motherboard only has SATA drive capability (aside from the IDE for the cds). All of Minerva's data is on two IDE drives. What is the easiest way to get the data from the IDE drives to the SATA disks? Would putting the old hard drives (temporarily) into the IDE ports be my best bet?Comment
-
Easiest ? I'd buy Acronis True Image from Newegg for $20 and have that do all the work. You can image the data over, but you will have to do a repair install of the Windows XP OS to get it to properly initialize and bot to the correct hard drive.What is the easiest way to get the data from the IDE drives to the SATA disks?Oh if a man tried to take his time on Earth and prove before he died what one man's life could be worth, well I wonder what would happen to this world ? - Harry ChapinComment
-
Nevermind...Comment
-
Yeah... I'd have put in the IDE slot, and just move the data over.
but then again, I'm a bit frugal, and don't spend money that I don't
have to. A little physical work for free beats paying for it.
Comment
-
Seeing as how my nifty IDE-to-SATA convertor isn't well-liked by the motherboard, I am going to have to go this route. Anyone care to share their experience of having an IDE hd and a SATA hd simultaneously? Namely, what jumper settings do I use on the IDE hd?Originally posted by Dead_And_GoneYeah... I'd have put in the IDE slot, and just move the data over.
but then again, I'm a bit frugal, and don't spend money that I don't
have to. A little physical work for free beats paying for it.Comment
-
They are independednt. if the IDE HD is the only one on the chain, set it to master. the sata drive has no "master/slave" configuration. all you REALLY need to worry about is making sure the BIOS is looking for the right drive to boot from. By default, most bios will set the default boot drive to the IDE variant.Originally posted by ThisElfRocksHardSeeing as how my nifty IDE-to-SATA convertor isn't well-liked by the motherboard, I am going to have to go this route. Anyone care to share their experience of having an IDE hd and a SATA hd simultaneously? Namely, what jumper settings do I use on the IDE hd?Originally posted by Dead_And_GoneYeah... I'd have put in the IDE slot, and just move the data over.
but then again, I'm a bit frugal, and don't spend money that I don't
have to. A little physical work for free beats paying for it.
Ther ereally is nothing to be concerned about other than just making sure the boot drive is listed properly to the one you want to boot from. no real jumper or pin settings to worry about.
Comment
-
OMG ITS WORKING!!!!!!!!!!!!11111111 Thanks guys!Comment
-
I'm looking at BF4, if it has enough players. Small community but very loyal to that game.
I bought it for 2 bucks, tried it out, runs...16 Mar 2025, 10:30 PM -
Ive had to get a new copy, but played a few games the last few weeks, Im so green its funny
Hey bar!8 Apr 2025, 06:27 PM -
Well, maybe Ill have to reinstall.7 Apr 2025, 10:07 PM
-
I'm researching server locations. check your pings, and post a screenshot...
https://www.nfoservers.com/networklocations.php
...17 Mar 2025, 10:34 PM -
Hey Tony!!!
Agreed! Its great to see!
Should jump in the discord, lots of daily chatter going on in there now
26 Mar 2025, 08:59 PM -
Wow, noticed that the Cain's Lair forums are comin' alive!! Be glad to squad up!...
26 Mar 2025, 08:01 PM
-
16 Mar 2025, 10:01 PM
-
I'm excited, it's looking like they're going back to the original BF3 and BF4 style!26 Mar 2025, 04:22 PM
-
Gonna look into it when I get home on the PS5, gotta kick kolt off of it temporarily26 Mar 2025, 04:13 PM
Comment